| | 线路电流 | 33.3 A 500 V 3 phases 15 kW 20 hp 47.3 A 380 V 3 phases 15 kW 20 hp | | | |
| | 视在功率 | 41 kVA 500 V 3 phases 15 kW 20 hp | | | |
| | 预期线路Isc | <= 22 kA 3 phases | | | |
| | 额定输出电流 | 33 A 4 kHz 500 V 15 kW 20 hp | | | |
| | ***瞬变电流 | 49.5 A 60 s 15 kW 20 hp | | | |
|
|
|
| | 速度范围 | 1...100 asynchronous motor in open-loop mode | | | |
| | 速度精度 | +/- 10 % of nominal slip 0.2 Tn to Tn | | | |
|
|
| | 制动力矩 | < 170 % with braking resistor | | | |
| | 非对称电机控制配置文件 | Voltage/frequency ratio, 2 points Voltage/frequency ratio, 5 points Flux vector control without sensor - Energy Saving, NoLoad law Flux vector control without sensor, standard Voltage/frequency ratio - Energy Saving, quadratic U/f | | | |
| | 同步电机控制配置模式 | Vector control without sensor | | | |
| | 调节回路 | Régulateur PID ajustable | | | |
| | 电机滑差补偿 | 自动 无论负载情况 不可用电压/频率比(2 或 5 点) Adjustable 0...300 % | | | |
| | 接地信号 | 1 LED 红色 设备电压 1 LED green CANopen run 1 LED red CANopen error 1 LED red drive fault | | | |
|
|
|
| | 电气连接 | Screw terminal 16 mm² AWG 6 power supply Screw terminal 0.5...1.5 mm² AWG 18...AWG 14 control 可拆卸螺钉端子 6...16 mm² AWG 8...AWG 6 motor/braking resistor | | | |
| | 紧固扭矩 | 0.5 N.m 4.4 lb/ft control 1.2 N.m 10.6 lb/ft motor/braking resistor 1.2 N.m 10.6 lb/ft power supply | | | |
| | 电源 | Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <= 10 mA overload and short-circuit protection | | | |
|
| | 模拟量输入类型 | Voltage AI1 0...10 V DC 30000 Ohm 10 bits Bipolar differential voltage AI2 +/- 10 V DC 30000 Ohm 10 bits Current AI3 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration) 250 Ohm 10 bits | | | |
| | 采样期间 | 2 毫秒 AI1, AI2, AI3 模拟 2 毫秒 AO1 模拟 | | | |
| | 响应时间 | 8 ms +/- 0.7 ms LI1...LI6 logic 2 ms R1A, R1B, R1C relay 2 ms R2A, R2C relay | | | |
| | 精度 | +/- 0.2 % AI1, AI2, AI3 for a temperature of -10...60 °C +/- 0.5 % AI1, AI2, AI3 for a temperature of 25 °C +/- 1 % AO1 for a temperature of 25 °C +/- 2 % AO1 for a temperature of -10...60 °C | | | |
| | 线性度误差 | +/- 0.2...0.5 % of maximum value AI1, AI2, AI3 +/- 0.3 % AO1 | | | |
|
| | 模拟输出 型号 | Software-configurable current AO1 0...20 mA 800 Ohm 10 bits Software-configurable voltage AO1 0...10 V 470 Ohm 10 bits | | | |
|
| | 输出型式 | Configurable relay logic R1A, R1B, R1C NO/NC 100000 cycles Configurable relay logic R2A, R2B NO 100000 cycles Logic LO | | | |
| | 最小却换容量 [Imin] | 5 mA 24 V DC configurable relay logic | | | |
| | ***开关电流 | 3 A 250 V AC resistive cos phi = 1 R1 4 A 30 V DC resistive cos phi = 1 R1 2 A 250 V AC inductive cos phi = 0.4 R1, R2 2 A 30 V DC inductive cos phi = 0.4 R1, R2 5 A 250 V AC resistive cos phi = 1 R2 5 A 30 V DC resistive cos phi = 1 R2 | | | |
|
| | 离散量输入类型 | Programmable (sink/source) LI1...LI4 24...30 V DC level 1 PLC Programmable as pulse input 20 kpps LI5 24...30 V DC level 1 PLC Switch-configurable PTC probe LI6 24...30 V DC Safe torque off STO 24...30 V DC 1500 Ohm | | | |
| | 离散量输入逻辑 | 正逻辑(源) LI1...LI6 < 5 V > 11 V Negative logic (sink) LI1...LI6 > 19 V < 13 V | | | |
| | 加速和减速倾斜 | S U CUS Deceleration ramp automatic stop DC injection Deceleration ramp adaptation Linear Ramp switching | | | |
|
| | 保护类型 | 输入断相 驱动 输出相线和接地之间的过流 驱动 过热保护 驱动 电机各相线之间短路 驱动 Thermal protection drive | | | |
|
| | 端口类型 | 1 RJ45 Modbus/CANopen 前面板 | | | |
|
|
|
| | 地址数 | 1...247 Modbus 1...127 CANopen | | | |
|
| | 电磁兼容性 | 1.2/50和8/20 µs复合波(测试) 级别 3 IEC 61000-4-5 抗快速瞬变 级别 4 IEC 61000-4-4 静电放电抗干扰 级别 3 IEC 61000-4-2 射频电磁场辐射抗扰度试验 级别 3 IEC 61000-4-3 抗射频场引起的传导波动 级别 3 IEC 61000-4-6 Voltage dips and interruptions immunity test IEC 61000-4-11 | | | |
|
|
|
|
| | 选项卡 | Communication card CANopen daisy chain Communication card CANopen open style Communication card DeviceNet Communication card Ethernet/IP Communication card Profibus DP V1 | | | |
|
|