扬州瑞浦DCL-100精小型电动执行器

易卖工控网（www.ymgk.com）提供”扬州瑞浦DCL-100精小型电动执行器”，产品详情：品牌/厂家：扬州瑞浦、型号：DCL-100、成色：全新、货期：期货 3天内发货、保修：365天，更多产品详情就上易卖工控网。

1．电气限位的调整 Adjustment of the limited location of electric

松开行程挡块的螺钉，用螺丝刀轻敲行程挡块，即可调整行程行行程开关挡块的角度，从而改变电气限位的开闭角度。最后，切实紧固好行程挡块的螺钉。5、10的行程挡块和行程开关布局图。详情联系王经理：153，8032，9557（wei 信同号）

Unalamp the screw that the joumey blocked one, rap the journey and block one with the screwdriver, i.e. the adjustable journey blocks the angle of one, thus change the holding and closing the angle of the location of electric limit. Finally, fasten the screw that the good journey blocked one conscientiously. 2040／50／60／100200的行程挡块和行程开关布局图 20/40/50 60/100/200 of the travel block lumps and travel switch overall arrangement picture

2．电器位的调整（开度型、智能型 Adjustment(tum on one degree of types, inte)of the potentiometer

a．电位器的电阻值为1K2、5K2。

The resistance valve of the potentionmeter is 1kn, 5KO

b．用手柄转动动阀门到全闭位置。

Rotate the valve and reach to close the position completely with the handle

C．松开电位器，转动动电位器齿轮，用万能表测量4－5接线端子间的电阻值，使4－5的电阻值到

52以下，紧固电位器固定螺钉。（如果是智能型的七线接插件连接时请测量对RV和RS两插插孔的电阻值）

Unclamp the potentionmeter rotate the gear wheel of the potentionmeter measure the resistance valve among4-5wiring sons of end with the universal meter nable the resistance valve of 4-under 50, fasten the potentionmeter fixed screw.(if please measuer the resistance value to RV and RS two jake when being that intelligent Line seven connects the plug-in package connection

注：手动操作时，不能过分超出全开，全关的极限位置，转角过大，会导致其部件的损坏

Note: At the time of manual operation, can t go beyond and is open excessively completel he terminal position that is closed completely. the comer is too big, will cause its part s damage

3．机械限位的调整

Adjustment of the mechanism spacing

a．用手柄转动到全开位置

Rotate to completely opening position with the handle

b．松开锁紧螺母，旋转调整螺钉，使只与机械挡挡块接触，然后反方向旋转螺钉半圈，锁紧螺毋。详情联系王经理：153，8032，9557（wei 信同号）

Unclamp the locknut, rotate and adjust the screwenable it and machinery block one and keep in touch, then, rotate semi circke of screw, the locknut in the opposite direction

c．同样的方法，可进行全闭位置的机械挡块的调整。

The same method, can close the adjustment of blocking one of machinery of the position completely.